You are here
Federal Spec TT-B-1325D Type 3 Airport Glass Beads Half Pallet
- US Federal Spec TT-B-1325D Type 3
- High visibility reflective paint markings
- Especially designed for runway and taxiway markings
- Get 1000 lbs of glass beads shipped on a pallet with 50 lb bags
Recommended For
Contractor 
Government 
Airport Description
Federal Specification TT-B-1325D Type 3 (Type III) high index reflective glass beads have become the FAAs glass bead of choice for airport runways. Night visibility is important and the TT-B-1325D Type 3 specification is designed to make the line markings on runways and taxiways even safer and continues to push the boundaries of reflective paint.
We sell a lot of line marking paint to airports across the country and the demand for a cost-effective Type 3 glass bead is always at the forefront of our sales calls. That's why we are more than happy to offer a 50lb bag that is priced right for the professionals and airport managers who need it. In addition, with an ROI index above 1.9, our glass beads will meet or exceed the TT-B-1325D Type III Federal Specification for airport runway and taxiway reflective paint requirements.
For most airports, especially small airports, you can get away with using Type 1 glass beads which is a lower index of refraction with a wider field of view. There are some airports, usually larger ones that prefer to use the higher index of refraction Type 3 glass beads. If you're unsure what you need, double check with your specification requirements but we are under the impression that it is up to the airport managers personal preference whether you need Type I or Type III. You can review the Report to Congress document in our literature tab above for more information on this decision.
You can figure to use approximately 5 to 6 pounds of glass beads, for every 1 gallon of paint.
Sold as a half pallet with 20 bags that each weigh 50 lbs, totaling 1000 lbs of glass beads.
Cost Analysis
The one big question we get about this product, is: "Why is it so much more expensive?"
The Type III specification from the US Federal Government, dictates that it must be a "High Index of Refraction". In most cases, this requires virgin glass, with no specific ingredients added to the manufacturing process. In contrast, Type I glass beads MUST be made from reclaimed scrap glass (soda lime cullet). Recycled glass is a lot easier and cheaper to manufacture than virgin glass when you're considering quality is the most important factor in Type III glass beads. Type 3 glass beads are also slightly larger in size than its Type 1 counterpart.
You can rest easy in knowing that our Type 3 airport beads come from US based manufacturing and distribution companies that pride themselves on quality products.
Unless you absolutely need Type 3 glass beads as dictated by federal specifications, or you need a narrow window of very high index of refraction, you might want to take a look at our Type I glass beads and save a ton of money.
You Might Like
Specifications
Bag Size | 50lbs |
Pallet Quantity | 20 |
Product Weight | 1000lbs |
Specification Type | TT-B-1325D Type 3 |
Refractive Index | Class A acc. to EN 1423 |
Bulk Weight | ~ 1,6 – 1,8 g/cm3 |
Hazardous Substances | As, Pb, Sb – Class 1 (< 200 ppm) |
Storage | Dry and sheltered; Can be stored for 24 months in the original container |
1 lb linear | 10ft @ 4" line width |
10 lb linear | 100ft @ 4" line width |
50 lb bag yield linear | 500 ft @ 4" line width |
1 lb square | 3.33 sq ft |
10 lb square | 33.3 sq ft |
50 lb bag yield square | 166.5 sq ft |
Note | Coverage yield may vary based on application method. Listed coverages are for a general idea only. |
Size (Mesh) | 20 - 50 |
Size (Microns) | 850 - 300 |
Size (mm) | 0.850 - 0.300 |
